HeveaBoard Berhad
Board Specification: Boards for interior fitments (including furniture) for use in dry condition (Type 13)
Requirement for specified mechanical properties
| Property | Test Method | Thickness (mm) | HB Test Result E1-725 18mm | HB Test Result E0-725 18mm | HB Test Result CARB Phase 2 C2-725 18mm | ||
|---|---|---|---|---|---|---|---|
| >6 to 13 | >13 to 20 | > 20 to 25 | |||||
| Bending Strength (N/mm²) | EN 310 | Min 13.0 | Min 13.0 | Min 11.5 | > 13 | > 13 | > 13 |
| MOE (N/mm²) | EN 310 | Min 1800 | Min 1600 | Min 1500 | > 2400 | > 2400 | > 2400 |
| Internal Bond (N/mm²) | EN 319 | Min 0.40 | Min 0.35 | Min 0.30 | > 0.45 | > 0.45 | > 0.45 |
| Screw Holding Edge (N) | BS 5669:1989 | Min 360 | Min 360 | Min 360 | > 500 | > 700 | > 700 |
| Surface Soundness (N/mm²) | EN 311 | Min 0.8 | Min 0.8 | Min 0.8 | > 1.20 | > 1.20 | > 1.20 |
| 24 hours Thickness Swelling (%) | EN 317 | Max 8.0 | Max 8.0 | Max 8.0 | < 6% | < 5% | < 5% |
| Moisture Content (%) | EN 322 | 5 - 13 | 5-13 | 5-13 | 5 - 8% | 5 - 8% | 5 - 8% |
Board Specification: Formaldehyde Emission Release
| Formaldehyde Emission Class | Requirement | HB Test Result E1-725 18mm | HB Test Result E0-725 18mm | HB Test Result CARB Phase 2 C2-725 18mm |
|---|---|---|---|---|
| E1 | Content ≤ 8 mg/100 g oven dry board | < 7 mg/100g od | - | - |
| E0 | Content ≤ 5 mg/100 g oven dry board | - | < 4 mg/100g od | - |
| CARB Phase 2 | Max 0.09 ppm | - | - | < 0.08 ppm |
Board Specification: Non-Load bearing boards for use in humid condition (Type 13)
Requirement for specified mechanical properties
| Property | Test Method | Thickness (mm) | HB Test Result M1-T2S 16mm | HB Test Result M0-T2S 18mm |
|---|---|---|---|---|
| 13 to 20 | ||||
| Bending Strength (N/mm²) | EN 310 | Min 14.0 | > 14 | > 14 |
| MOE (N/mm²) | EN 310 | Min 1950 | > 2600 | > 2600 |
| Internal Bond (N/mm²) | EN 319 | Min 0.45 | > 0.50 | > 0.50 |
| Screw Holding Edge (N) | BS 5669:1989 | n.a | > 700 | > 700 |
| Surface Soundness (N/mm²) | EN 311 | Min 0.8 | > 1.20 | > 1.20 |
| 24 hours Thickness Swelling (%) | EN 317 | Max 14.0 | < 10% | < 8% |
| Internal Bond After Cyclic (N/mm²) | EN 321 | Min 0.13 | > 0.20 | > 0.20 |
| Thickness Swelling After Cyclic (%) | EN 321 | Max 13.0 | > 12.0% | > 12.0% |
| Moisture Content (%) | EN 322 | 5 - 13 | 5 - 8% | 5 - 8% |
Board Specification: Formaldehyde Emission Release
| Formaldehyde Emission Class | Requirement | HB Test Result M1-T2S 16mm | HB Test Result M0-T2S 18mm |
|---|---|---|---|
| MUF E1 | Content ≤ 8 mg/100 g oven dry board | < 6 mg/100g od | - |
| MUF E0 | Content ≤ 5 mg/100 g oven dry board | - | < 4 mg/100g od |
